Wysiwash Sanitizer-V

The WYSIWASH Sanitizer-V includes the all new Flow Control Valve! It's so easy to use, you will clean more often with increased effectiveness. Simply connect the Applicator to a hose and spray. There is no need to worry about proper cleanser dispensing - it's automatic. Don't forget to purchase WYSIWASH Jacketed Caplets! - CAUTIONS/WARNINGS:DO NOT USE WITH AMMONIA BASED PRODUCTS Ammonia and chlorine-based cleaning products should never be combined. In the event that an accidental mixture occurs, immediately evacuate all people and animals from the area and call local emergency services. WATER PRESSURE & PRESSURE SURGES Water pressure over 70 psi can damage Wysiwash equipment. This includes water pressure surges (water hammer) that exceed 70 psi. HARD WATER If you have hard water, we recommend soaking your Wysiwash Sanitizer-V or Sanitizer Pro in vinegar monthly. (See Build Up for instructions.) - DIRECTIONS:Sanitizing With Wysiwash Step 1: Turn on the hose. Step 2: To turn on the unit, twist the valve on top of the nozzle. Begin with a gentle mist, not a targeted spray. Misting first prevents pathogens from becoming airborne. Step 3: PRIME: Spray into a drain or bucket to prime the system. This ensures that the solution is at an effective concentration and any concentrate is flushed out. New Caplet: Prime for 1 - 2 minutes. Previously used caplet: Prime 30 - 40 seconds. Step 4: After the whole area has been sprayed with a gentle mist, use the pressure sprayer on heavily soiled areas to remove any remaining organic waste. To adjust the spray, twist the sleeve on the stem of the nozzle to adjust the spray. Step 5: Allow Wysiwash to set for 2 minutes. OPTIONAL RINSING: For uncoated metal or high gloss surfaces, we recommend rinsing. Step 6: Either squeegee, or allow the area to completely air dry. Draining the Wysiwash Sanitizer-V Draining is key to keeping your Wysiwash unit in good shape. Drain Wysiwash every time you use it. NOTE: Take caution to avoid contact with skin and clothing while draining. The drained solution is more concentrated and may stain/irritate skin. Rinse the area where Wysiwash has been drained to avoid chemical spots. Step 1: Make sure the Flow Control Valve is OFF. Step 2: Disconnect the Sanitizer-V from the Female Quick Connector by sliding the "neck" of the female toward the hose side again to release. Step 3: In a bucket, drain, or sink, turn the Sanitizer-V upside down and point the valve downward. Step 4: Turn the Flow Control Valve on to allow the solution to drain. The bottom of the Caplet Container, should be pointed upwards at a slight angle. This allows water to drain from the bottom of the Caplet Container. Step 5: Store the Sanitizer-V in this position to maximize the life of your caplets. - INGREDIENTS:See Product For Details - MATERIAL/COMP:Solid - STORAGE/DISPOSAL REQ:See Product For Details - HEIGHT(INCHES): 7.000 - WIDTH(INCHES):3.000 - LENGTH(INCHES):7.000 Brand: Wysiwash Manufacturer: Ingredients: See Product For Details Directions: Sanitizing With Wysiwash Step 1: Turn on the hose. Step 2: To turn on the unit, twist the valve on top of the nozzle. Begin with a gentle mist, not a targeted spray. Misting first prevents pathogens from becoming airborne. Step 3: PRIME: Spray into a drain or bucket to prime the system. This ensures that the solution is at an effective concentration and any concentrate is flushed out. New Caplet: Prime for 1 - 2 minutes. Previously used caplet: Prime 30 - 40 seconds. Step 4: After the whole area has been sprayed with a gentle mist, use the pressure sprayer on heavily soiled areas to remove any remaining organic waste. To adjust the spray, twist the sleeve on the stem of the nozzle to adjust the spray. Step 5: Allow Wysiwash to set for 2 minutes. OPTIONAL RINSING: For uncoated metal or high gloss surfaces, we recommend rinsing. Step 6: Either squeegee, or allow the area to completely air dry. Draining the Wysiwash Sanitizer-V Draining is key to keeping your Wysiwash unit in good shape. Drain Wysiwash every time you use it. NOTE: Take caution to avoid contact with skin and clothing while draining. The drained solution is more concentrated and may stain/irritate skin. Rinse the area where Wysiwash has been drained to avoid chemical spots. Step 1: Make sure the Flow Control Valve is OFF. Step 2: Disconnect the Sanitizer-V from the Female Quick Connector by sliding the "neck" of the female toward the hose side again to release. Step 3: In a bucket, drain, or sink, turn the Sanitizer-V upside down and point the valve downward. Step 4: Turn the Flow Control Valve on to allow the solution to drain. The bottom of the Caplet Container, should be pointed upwards at a slight angle. This allows water to drain from the bottom of the Caplet Container. Step 5: Store the Sanitizer-V in this position to maximize the life of your caplets. Cautions: DO NOT USE WITH AMMONIA BASED PRODUCTS Ammonia and chlorine-based cleaning products should never be combined. In the event that an accidental mixture occurs, immediately evacuate all people and animals from the area and call local emergency services. WATER PRESSURE & PRESSURE SURGES Water pressure over 70 psi can damage Wysiwash equipment. This includes water pressure surges (water hammer) that exceed 70 psi. HARD WATER If you have hard water, we recommend soaking your Wysiwash Sanitizer-V or Sanitizer Pro in vinegar monthly. (See Build Up for instructions.) Storage: See Product For Details